0-856-16 Durite 12V Modified Wave Voltage Inverter 110V Output - 1500W

 Durite 0-856-16, 12VDC 1500W modified wave voltage inverter with 110 Volts AC output. Used for industrial on-site field service engineer's work vans that include working in factories and store development site work.

• Input: 12VDC (12V to 15V DC).
• Output: 110VAC 50Hz.
• Rated at 1500 Watts (1.5kW), continuous.
• Quiescent (inactive) current less than 0.60A.
• Remote available to purchase separately, part number: 0-856-98

Protection Against

• Overload.
• Over-temperature.
• Low battery.
• High input voltage.
• Short circuit.

Supplied With

• A 3-Pin 110V socket outlet to BS4343.
• On-Off switch.
• LED indicators for voltage and consumption.

Dimensions

• Length: 240mm.
• Width: 408mm.
• Height: 76mm.

Warnings for Translation

• Read all instructions before attempting to install or use the inverter.
• High voltage, 110 Volts AC, is generated by this unit.
• Do not use it with wet hands or near water.
• This unit is only suitable for 12 Volts DC electrical systems with negative earth.
• To supply 110 Volts 50 Hz loads of < 1500 Watts.
• Do not connect to any other AC power source.

Installation Instructions

 Disconnect all battery leads, -ve leads first, before installing the inverter.

 Locate a suitable position for the inverter and fit it securely. The site chosen should be:

• Well ventilated.
• Not exposed to direct sunlight or heat source.
• Away from water or moisture.
• Out of reach of children.
• Away from any flammable or heat-sensitive substance.

 Connect the Black 12 Volts -ve terminal to the negative side of the supply source and the Red 12 Volts +ve terminal to a fused positive supply source. Use a minimum of 25.0mm² cable and keep all cable runs as short as possible.

 Connect the inverter case ground terminal to the chassis ground when installing in a vehicle, the vessel’s grounding system in a boat or to earth in a fixed location. The case ground terminal is connected to the ground terminal in the AC outlet socket.

 If using an additional remote control (part number to purchase: 0-856-98), fix the remote control in a suitable position and insert the connector into the remote control socket on the inverter control panel.

Operating Instructions

1. Ensure that the inverter is supplied by a 12-14 Volts DC negative earth system and that the load requires <1500 Watts at 110 Volts 50Hz AC.
2. Plug the appliance into the inverter and then turn on the inverter’s power switch. The LED will illuminate to indicate AC power is present, then switch on the appliance. Always turn on the inverter before turning on loads individually. If using the optional remote control, ensure the control panel power switch is set to ‘Remote’, then use the remote ‘On/Off’ switch as the inverter power switch.
3. Switch off the inverter when not in use or when heavy current is drawn from the dc supply, e.g. when starting an engine from the same supply source.
4. Battery voltage and current bar graphs indicate supply voltage and current. In normal operation, the inverter will operate in the green region. The inverter can operate in the current yellow zone for short periods, and a protective shutdown will occur if used in the red zone.
5. If the inverter beeps but is still supplying AC output, this indicates a low supply voltage; switch off the inverter to preserve battery voltage. If left on, the inverter will automatically shut down when the supply voltage falls to approximately 10.0 ± 0.5 Volts.
6. The Overtemp indicator illuminates when the inverter has shut down due to overheating. The inverter will restart automatically once it has cooled down.
7. The overload indicator illuminates when the inverter has shut down due to output short-circuit or gross overloading. If this occurs, switch the inverter off and correct the cause before switching the inverter on again.

Troubleshooting

 If the inverter beeps or does not appear to be functioning correctly, check the following:

1. Low dc supply voltage, supply voltage <10.5 ± 0.5 Volts.
2. Low dc voltage shutdown, supply voltage <10.0 ± 0.5 Volts.
3. Overload shutdown, check load requirement is <1500 Watts. The warning signal is constant short beeps, and a continuous tone indicates shutdown.
4. Thermal shutdown, switch off, allow the inverter to cool down and reduce load.
5. Wiring, terminals and connections.

Specifications