0-441-50 Durite R65 Slimline High Intensity 6 Amber LED Warning Light

 Durite 0-441-50 12 or 24 Volts DC R65 Slimline High Intensity 6 Amber LED Warning Light with 10 flash patterns.

• Voltage: 12V-24VDC (10V-30VDC).
• Amber 6 x 3W LED ultra-high intensity LED warning light.
• 10 programmable flash sequences.
• Protected to IP67.
• CE, ECE R65 Class 1 and SAE Class 1 R10 approved.

Dimensions

• Length: 120mm.
• Width: 32mm.
• Height: 14.4mm.

Warnings

Before using this unit, please read these instructions carefully. Take special care to follow the warnings and safety suggestions listed below. Keep these instructions for future reference.

Safety Warning

1. Proper installation of this product requires the installer to understand automotive electronics, systems and procedures well.
2. If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling begins. Also, de-burr the holes and remove any metal shards or remnants.
3. Do not install this product or route any wires in the deployment area of your airbag. Equipment mounted or located in the airbag deployment area will damage or reduce the effectiveness of the airbag or become a projectile that could cause serious personal injury or death. Refer to your vehicle owners manual for the airbag deployment area. The User/Installer assumes full responsibility for determining the proper mounting location based on providing ultimate safety to all passengers inside the vehicle.
4. Do not attempt to activate or control this device in a hazardous driving situation.
5. This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could result.
6. Use only soap and water to clean the outer lens. The use of other chemicals could result in premature lens cracking (crazing) and discolouration. Lenses in this condition have significantly reduced effectiveness. Inspect and operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
7. It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.
8. A good electrical connection to the chassis ground must be made for this product to operate at optimum efficiency. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post.

Mounting

• Place the unit against the mounting surface.
• Mark the areas where the mounting holes are to be drilled. Confirm that no vehicle parts could be damaged by the drilling process.
• Using a bit size for a no. 304 metal screw, drill two mounting holes, a 0.5-inch diameter. Wire passage hole(s) must also be drilled. Thoroughly de-burr all hole(s).
• Pass the wires through the hole(s) in the gasket and the wire passage hole(s) in the mounting surface. Fix the light head to the mounting surface.

Flash Patterns - 10 Flash Patterns Total

• Random
• Single (split)
• Double (split)
• Quint (split)
• Triple (all)
• Quint (all)
• Triple (split)
• Single (all)
• Quint (all)
• Single-Quad (split)

Grouping for Simultaneous Flash:

• Connecting all units with black, red and yellow wires will synchronize all light heads. Touching the red wires to the yellow wires for 5 seconds will change the flash pattern (all units must be reset individually on the first same pattern to remain synced together on the same pattern). If you want to synchronise the flash pattern, touching the red wires to the yellow wires for 1 second will change the flash pattern. Note: If the light cannot be synced, please repeat STEP 1.

Grouping for Alternating Flash:

• Connecting all units with black, red and yellow wires will synchronize all light heads. Touching the red wires to the yellow wires for 5 seconds will change the flash pattern (all heads must be reset individually on the same pattern first to remain synced together on the same patterns). Connecting one unit or some units green wires to the red wire will make them alternating flash. Do not connect the Yellow to the red wires; all units remain synced together on the same patterns. If the units cannot achieve alternating flash, please repeat STEP 1.

Specifications