0-467-40 20VDC 1000Nm Fast Charge Half Inch Brushless Impact Wrench

0-467-40 Durite 20VDC 1000Nm fast charge half-inch brushless impact wrench with a brushless motor and 3 intelligent gear settings.

• Durite one battery fits all.
• Features a brushless motor.
• Max torque 1000Nm.
• Impact rate: 0-2300IPM.
• 3 intelligent gear settings 0-950/0-1500/0-1800rpm
• Weight including battery 3.545kg; excluding battery 2.870kg.
• LED work light and belt clip.
• Brushless motor with reverse/forward function.
• Fast 1-hour charge time.
• Full kit supplied with a wrench, battery and charger in a BMC case
• CE, UKCA, and RoHS approved.

Associated Product

Replacement/additional/spare battery 0-467-42 - (available separately)

Power Tool Use and Care

• Do not force the power tool. Use the proper power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or sticking of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to stick and are easier to control.
• Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Using the power tool for operations different from intended could lead to a hazardous situation.

Charging / Batteries

• Charge the battery only with the charger that is supplied with the tool.
• Do not touch the contacts in the charger.
• Do not expose the tool/charger/battery to rain.
• Do not charge the battery in damp or wet environments. Store the tool/charger/battery in locations where the temperature will not exceed 50 degrees centigrade or drop below 0 degrees centigrade.
• Do not use the charger when damaged.
• Do not use a charger when the cord or plug is damaged.
• Do not use the battery when damaged; it should be replaced immediately.
• Do not disassemble the charger or battery.
• Do not attempt to recharge non-rechargeable batteries with the charger.
• If you anticipate long periods of non-use for the tool, it is best to unplug the charger from its power source.

When Connecting New 3-Pin Plug (U.K. Only)

• Do not connect the blue(= neutral) or brown(= live) wire in the chargers cord to the earth terminal of the plug.
• If the old plug is cut off the chargers cord, it must be disposed of safely and not left unattended.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Cleaning and Maintenance

• When not in use, the tool should be stored in a dry, frost-free location, out of reach of children. Keep the ventilation slots of the tool clean at all times and prevent any foreign matter from entering. If the housing of the tool requires cleaning, do not use only solvents but a moist, soft cloth. Blow out the ventilation slots with compressed air periodically.

Operation

• Always switch off the tool before insertion or removal of the battery. Installing the battery holding the tool upright, and picking up the battery in your opposite hand, push the battery release button and insert the battery until it clicks into place. Do not use excessive force when inserting the battery; if
• the battery does not slide in easily; it is not being inserted correctly; it is also possible that there could be damage to the battery, battery terminals or the tool.
• The direction of rotation can be changed with the forward/release selector, which is located above the variable speed switch. Push the forward/reverse selector hard left to select the forward position. Push the forward/ reverse selector hard right to select the reverse position. Do not change the direction of rotation while the tool is in motion. To lock the tool put the selector in the centre position. This can also prevent the accidental starting of the tool.

LED Lights

• The tool has 1 LED light built into the unit. The LED light is located above the variable speed switch.
• The LED light turns on automatically when you depress the variable speed switch.
• The LED light illuminates dark areas in tight corners to assist with the view of the workplace.

LED Power Indication

• 3 LEDs will show you the capacity of the battery.

Removing the Battery

• Depress the battery release button and gently pull the battery out of the tool.

Charging the Battery

• The tool has been shipped in a quick charge condition. You should charge it prior to use. Plug the charger into a power outlet. Insert the battery into the charger. The recess of the battery terminals will have a firm connection. Upon proper contact, the red and green lights will illuminate, and when fully charged, the red light will go out, and only the green light will be illuminated.

NOTE: If the charging light fails to come on

• Check the charger is securely plugged into the wall outlet and is switched on.
• Check the battery is firmly seated on the charger.
• The battery will take 1 hour to charge. Charging starts automatically. Remove the battery from the charger once charged; otherwise, it may become damaged.
• When the battery is hot, it may not charge immediately. This is a feature of the lithium-ion battery, as charging hot batteries shortens their life. In this case, the green light only will illuminate when the battery is inserted into the charger. The battery needs to cool, which may take several minutes, and it will automatically start charging once cooled.

Initial Charge

• Charge your battery for 1 hour, then use it until it runs down and only slowly operates.
• Repeat this charge and discharge process approximately 4-5 times, ensuring that the battery performs to its highest capacity. The charger will turn off when the battery is fully charged.

Important Charging Notes

• The charger and battery may become warm to the touch while charging. This is a normal condition and does not indicate a problem. Use the charger at normal room temperatures whenever possible. To prevent overheating, do not cover the charger and do not charge the battery in direct sunlight or near heat sources.

NOTE: If the battery does not charge properly

• Check the current at the power outlet by plugging in a lamp or other appliance.
• If charging problems persist, check the complete tool by an electrician or a power tool repairer.

Battery

• The length of service from each charging cycle will depend on the type of work you are doing. The battery in this tool has been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out.
• We suggest storing and charging your battery in a cool area to obtain the longest possible battery life. Temperatures above or below normal room temperature will shorten battery life.
• Never store batteries in a discharged condition. Recharge them immediately after they are discharged. All batteries gradually lose their charge. The higher the temperature, the quicker they lose their charge. If you store your tool for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery life.

Specifications